Page 1 of 2
Berkley Quick Set rod holders on Ram mounts
Posted: 14 Oct 2019, 21:19
by 4liters
Anyone put Berkley Quick Set rod holders on a Ram mount?
I'm curious to see how people have done it, I really like the Quick Set rod holders as it's a lot easier to get the rod out when there's something heavy on the other end and the rod holder is past your toes.
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 14 Oct 2019, 21:49
by laneends
Think cheater might have
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 14 Oct 2019, 22:01
by peatop
I've been thinking about how to mount them (quick sets) to the H rail and thinking something similar, The holes on the square mount ram ball would line up pretty close to the quick set mounts although i don't like the quick set mounts and prefer using scotty instead, after using ball mounts on my sounder i can see why people like them im impressed.
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 15 Oct 2019, 09:01
by cheaterparts
4liters wrote:Anyone put Berkley Quick Set rod holders on a Ram mount?
I'm curious to see how people have done it, I really like the Quick Set rod holders as it's a lot easier to get the rod out when there's something heavy on the other end and the rod holder is past your toes.
laneends wrote:Think cheater might have
Yes mate I fitted the quick set bases to 1 inch ram balls. That’s what I use on my front mounts for the stealth.
I cut off the bottom piece from the square section of the quick set mount and though bolted it to the ram ball - I also did away with the wing nut adjuster and used a plain stainless nut and bolt as the adjustments now for rod angle both up and down - side to side are all done with the ram mount - it came it fairly neat and works a treat
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 29 Oct 2019, 18:07
by 4liters
cheaterparts wrote:4liters wrote:Anyone put Berkley Quick Set rod holders on a Ram mount?
I'm curious to see how people have done it, I really like the Quick Set rod holders as it's a lot easier to get the rod out when there's something heavy on the other end and the rod holder is past your toes.
laneends wrote:Think cheater might have
Yes mate I fitted the quick set bases to 1 inch ram balls. That’s what I use on my front mounts for the stealth.
IMG_0553.JPG
IMG_0555.JPG
I cut off the bottom piece from the square section of the quick set mount and though bolted it to the ram ball - I also did away with the wing nut adjuster and used a plain stainless nut and bolt as the adjustments now for rod angle both up and down - side to side are all done with the ram mount - it came it fairly neat and works a treat
Only just saw these lol
Is that one of these balls with the square base?
And then a hole drilled down the centre of the square section of the rod holder for a bolt that goes through to the centre of the ball mount?
What are the two bolts through the the ball mount for?
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 29 Oct 2019, 18:24
by Seasherpa
4liters wrote:
What are the two bolts through the the ball mount for?
To stop the base from turning and loosening off
I had a set on the Fisha 460, they are a very handy but very exxy addition
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 29 Oct 2019, 18:36
by 4liters
Seasherpa wrote:4liters wrote:
What are the two bolts through the the ball mount for?
To stop the base from turning and loosening off
I had a set on the Fisha 460, they are a very handy but very exxy addition
Makes sense.
I like the idea of having something like this that is quite adjustable rather than the fixed rod holders I've used previously, it hopefully won't cost a whole lot more than getting the stainless frames put together.
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 29 Oct 2019, 19:53
by cheaterparts
you guys have it all worked out
yes I cut the bottom fitting of the berkley bases and the is already a bolt that goes through the burkley base to probably strengthen the unit
then you need to tap out the ram ball and the hole from memory is tapping size for 6 mm or 1/4 UNC then its just bolt them together with a stainless button head - as Eoin said the small spare bolts I added just to keep the base lined up on the ram ball - twisting may have loosened it off
the work out tidy and work very well
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 29 Oct 2019, 19:55
by 4liters
Does the ram ball need to be tapped out or can I just drive a bolt into it? Not as neat but I don’t have anything for cutting threads.
Re: Berkley Quick Set rod holders on Ram mounts
Posted: 29 Oct 2019, 21:14
by cheaterparts
4liters wrote:Does the ram ball need to be tapped out or can I just drive a bolt into it? Not as neat but I don’t have anything for cutting threads.
well I tapped mine - but then I'm more of an engineer than a butcher